Max RB217 Instrukcja Użytkownika

RB517 RB397 RB217RE-BAR TYING TOOLOPERATING AND MAINTENANCE MANUALBEFORE USING THIS TOOL, STUDY THIS MANUAL TO ENSURE SAFETY WARNING AND INS

1015. PRIOR TO USING THE TOOL.• Make sure that the safety features function properly. If they do not, avoid using the tool.Trigger LockThe Trigger can

113. SPECIFICATIONS AND TECHNICAL DATA1. NAME OF PARTS2. TOOL SPECIFICATIONSPRODUCT NO. RB517 RB397 RB217WEIGHT 5.3lbs (2.4kg) (Battery in-cluded)5.3l

12<Battery charger><Battery pack>3. WIRE SPECIFICATIONSBATTERY CHARGER:Use only an authorized Battery charger, MAX JC925.Product name LITH

134. TECHNICAL DATA1 NOISEA-weighted single-event ------ LWA, 1s, d 84 dBsound power levelA-weighted single event ------ LpA, 1s, d 73 dBemission soun

144. BATTERY INSTRUCTIONS1. Charging• Before removing the Battery pack from the tool, set the Main switch at OFF and lock the Trigger.1 A Pack cap tha

15When the Battery pack is at low tem-peratureWhen the Battery pack is at low temperature, its charging is automatically suspended until its tem-perat

16(1) After you have recharged the battery pack, remove it from the charger.(2) Unplug the charger power cord from the wall socket.Regarding tying tim

17Indication of Quick Charger Lamps∗For batteries those are at low temperatures (50°F (10°C) or lower), charging time must be extended longer.About th

18Service Life of the Battery PackIf any condition described below is observed, the battery pack is at the end of its service life. Re-place it with a

192 Peel off the tape fixing Tie-Wire by about 2" (5cm). Stretch out the tip of the wound Tie-Wire.BE SURE TO USE ONLY THE SPECIFIED TIE-WIRE (MA

2INDEXDEFINITIONS OF SIGNAL WORDSWARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.C

20If the window is dirty and the pipe po-sition can not be confirmedOpen the window and wipe off the dirt on the in-side of the window with a soft clo

210 Tool feeds the wire about 6" (150 mm) and cuts the wire automatically.Remove the cut end of the wire with pliers.a Unlock the Trigger before

223 Slide the Reel stopper to release the Reel holder and remove the Tie-Wire.4 Mount the new Tie-Wire. (Refer to the Tie-Wire mounting method explana

232 This dial allows you to set 3 wraps / tie or 4 wraps / tie and also you can adjust the torque.To increase the tension, turn it in the coun-tercloc

244. Tension adjustment1 Be sure to turn the Main switch OFF, to lock the Trigger and detach the Battery pack.2 This dial allows you to adjust wire te

254. Wire length adjustment1 Be sure to turn the main switch OFF, to lock the trigger and detach the battery pack.2 The feed dial is a mechanism to ad

265. For proper tightness1 Tilt the tool 45° angle to the crossed re-bars.2 Apply the tool perpendicularly to the surface of the crossed re-bars.Durin

276. MAINTENANCE1 Regularly inspect the toolIn order to maintain the performance of the tool, periodically clean up and inspect the tool.2 Do not lubr

283. Remove the cutter and the fixed cutter, and clean them. (The removable parts are the cutter, fixed cutter, wire guide A and cutter plate unit.)As

297. Make sure that arm B is securely assem-bled and tighten the 2 (plated) hexagon socket head bolts M3 × 6. (Tightening torque: 15.2lbF·inch (172cN·

3INDEX1. GENERAL POWER TOOL SAFETY WARNINGS...32. RB517/397/217 SAFETY FEATURES ...63. SPECIFICATIONS AND TECHNI

30Assembling• Assemble the fixed cutter so that the large hole is set to the rear side and the small hole is set to the top side.4. Insert the step pi

318. STORAGEDo not store the tool in a cold weather environ-ment. Keep the tool in a warm area.When not in use, the tool should be stored in a warm an

329. TROUBLE SHOOTING/REPAIRSThe troubleshooting and/or repairs shall be carried out only by the MAX CO., LTD. authorized distribu-tors or by other sp

333. Trigger ON → Wire sent out.Sending of wire is stopped half-way.Four short beeps repeat-ed(Pipipipi, pipipipi, ...)Tie-Wire is not set in the too

• The content of this manual might be changed without notice for improvement.ATTENTION:The product you have purchased is powered by a Li-ion battery w

4• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.• Do not abuse the cord.

5Power tools are dangerous in the hands of untrained users.• Maintain power tools. Check for mis-alignment or binding of moving parts, breakage of par

62. RB517/397/217 SAFETY FEATURES1. INSPECT THE PARTS BEFORE MOUNT-ING THE BATTERY PACK• Examine the screws to make sure they are securely tightened.I

77. NEVER OPERATE THE TOOL UNDER ANY ABNORMAL CONDITIONIf the tool is not in good working order, or if any abnormal condition is noticed, switch it of

83 Never use a transformer4 Never connect the Battery charger to an engine generator direct-current power supplyThe charger will break down or be dam-

912Avoid continual use of the Battery chargerRest the Charger for 15 minutes between charges to avoid functional trouble with the unit.13Any objects t