Max RB397(CE) Instrukcja Użytkownika

RB397(CE) RB217(CE)RE-BAR TYING TOOLORIGINAL USER MANUALOriginal instructionsENGLISHBEFORE USING THIS TOOL, STUDY THIS MANUAL TO ENSURE SAFETY WAR

113. SPECIFICATIONS AND TECHNICAL DATA1. NAME OF PARTS2. TOOL SPECIFICATIONSPRODUCT NO. RB397 RB217WEIGHT 2.4kg (5.3lbs) (Battery included) 2.4kg (5.3

12<Battery charger><Battery pack>3. WIRE SPECIFICATIONSBATTERY CHARGER:Use only an authorized Battery charger, MAX JC928.Product name MAX

134. TECHNICAL DATA1 NOISEA-weighted single-event ------ LWA, 1s, d 82 dBsound power levelA-weighted single event ------ LpA, 1s, d 71 dBemission soun

144. BATTERY INSTRUCTIONS1. Charging• Before removing the Battery pack from the tool, set the Main switch at OFF and lock the Trigger.1 A Pack cap tha

15When the Battery pack is at low tem-peratureWhen the Battery pack is at low temperature, its charging is automatically suspended until its tem-perat

16(1) After you have recharged the battery pack, remove it from the charger.(2) Unplug the charger power cord from the wall socket.Regarding tying tim

17Indication of Quick Charger Lamps∗ For batteries those are at low temperatures (10°C (50°F) or lower), charging time must be extended longer.Charger

18Service Life of the Battery PackIf any condition described below is observed, the battery pack is at the end of its service life. Re-place it with a

192 Peel off the tape fixing Tie-Wire by about 5cm (2"). Stretch out the tip of the wound Tie-Wire.BE SURE TO USE ONLY THE SPECIFIED TIE-WIRE (MA

20If the window is dirty and the pipe po-sition can not be confirmedOpen the window and wipe off the dirt on the in-side of the window with a soft clo

3INDEX1. GENERAL POWER TOOL SAFETY WARNINGS...32. RB217/397 SAFETY FEATURES ...63. SPECIFICATIONS AND TEC

210 Tool feeds the wire about 150 mm(6") and cuts the wire automatically.Remove the cut end of the wire with pliers.a Unlock the Trigger before u

223 Slide the Reel stopper to release the Reel holder and remove the Tie-Wire.4 Mount the new Tie-Wire. (Refer to the Tie-Wire mounting method explana

232 This dial allows you to adjust wire tension torque slightly.To increase the tension, turn it in the coun-terclockwise.To decrease the tension, tur

244. Wire length adjustment1 Be sure to turn the main switch OFF, to lock the trigger and detach the battery pack.2 The feed dial is a mechanism to ad

255. For proper tightness1 Tilt the tool 45° angle to the crossed re-bars.2 Apply the tool perpendicularly to the surface of the crossed re-bars.Durin

266. MAINTENANCE1 Regularly inspect the toolIn order to maintain the performance of the tool, periodically clean up and inspect the tool.2 Do not lubr

273. Remove the cutter and the fixed cutter, and clean them. (The removable parts are the cutter, fixed cutter, wire guide A and cutter plate unit.)As

287. Make sure that arm B is securely assem-bled and tighten the 2 (plated) hexagon socket head bolts M3 × 6. (Tightening torque: 172cN·m (15.2lbF·inc

29Assembling• Assemble the fixed cutter so that the large hole is set to the rear side and the small hole is set to the top side.4. Insert the step pi

308. STORAGEDo not store the tool in a cold weather environ-ment. Keep the tool in a warm area.When not in use, the tool should be stored in a warm an

4• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.• Do not abuse the cord.

319. TROUBLE SHOOTING/REPAIRSThe troubleshooting and/or repairs shall be carried out only by the MAX CO., LTD. authorized distribu-tors or by other sp

323. Trigger ON → Wire sent out.Sending of wire is stopped half-way.Four short beeps repeat-ed(Pipipipi, pipipipi, ...)Tie-Wire is not set in the too

EC DECLARATION OF CONFORMITYWe hereby declare that the product titled in this instruction manual conforms to the essential health and safety requireme

• The content of this manual might be changed without notice for improvement.4008870101008-00/01PRINTED IN JAPANCamerastraat 191322 BB Almere The Neth

5Power tools are dangerous in the hands of untrained users.• Maintain power tools. Check for mis-alignment or binding of moving parts, breakage of par

62. RB217/397 SAFETY FEA-TURES1. INSPECT THE PARTS BEFORE MOUNT-ING THE BATTERY PACK• Examine the screws to make sure they are securely tightened.Inco

77. NEVER OPERATE THE TOOL UNDER ANY ABNORMAL CONDITIONIf the tool is not in good working order, or if any abnormal condition is noticed, switch it of

82 Charge the Battery from AC between 100V and 240V wall socketsFailure to do so may result in overheating, or inadequate charging possibly causing se

911Charge the Battery pack in a tempera-ture range of 5°C (41°F) to 40°C (104°F)12Avoid continual use of the Battery chargerRest the Charger for 15 mi

1015. PRIOR TO USING THE TOOL.• Make sure that the safety features function properly. If they do not, avoid using the tool.Trigger LockThe Trigger can